Used Victa Supertrak 200 Wheel
Rear wheel to suit most Victa rotary lawn mowers. Suits axle diametre of 9/16" (14mm). Overall wheel diametre 8 inches (200mm). Includes retaining clip and wheel trim. Wheel has one bush an one ball bearing fitted.
NO LONGER AVAILABLE VICTA82
Used Victa 8 inch Wheel
Rear wheel to suit most Victa rotary lawn mowers. Suits axle diametre of 9/16" (14mm). Overall wheel diametre 8 inches (200mm). Includes retaining clip and wheel trim. Wheel has one bush an one ball bearing fitted.
NO LONGER AVAILABLE VICTA82AUsed Victa Electric Start Assembly
Fits compatible Victa 160cc Power Torque engines. Complete system, tested and reay to install. Includes wiring harness, ignition key and barrel, fuse holder, pinion cover, module, ignition coil wiring harness (for earthing) and two mounting screws. Electric Starter OEM Number ST12778A.
NO LONGER AVAILABLE VICTA52
Used Victa Electric Start Battery Holder
1 in stock
Used Victa Power Torque Air Filter Housing and Intake Snorkel Assembly
Includes throttle lever and cable, screw & nut, rubber carburettor adaptor, clamp and snorkel clip.
NO LONGER AVAILABLE VICTA51
Used Victa Power Torque Air Filter Housing and Intake Snorkel Assembly
Includes throttle lever and cable, screw & nut, rubber carburettor adaptor, clamp and snorkel clip.
NO LONGER AVAILABLE VICTA70Used Victa Power Torque Ignition Coil Assembly
Built in module type. Includes wiring harness, PVC terminal cover and pin grommet.
OEM Number MA05599A
NO LONGER AVAILABLE VICTA27Used Victa Power Torque Ignition Coil Assembly
Built in module type. OEM Number MA05599A
NO LONGER AVAILABLE VICTA27B
Used Victa Power Torque Igniton Coil Assembly
Includes 2 x screws. Please note that this unit must be used with a module. OEM Number MA05556A
NO LONGER AVAILABLE VICTA27A
Used Victa Ignition System Assembly
Fits Victa 125cc 70 series Mark 3 two stroke engines. Ready to install.
1 in stock
Used Victa G3 Carburettor Assembly
Fits Victa 125cc 70 series Mark3 two stroke engines, as fitted to Victa Imperial cylinder mowers. Fully dismantled, cleaned, inspected and tested.
NO LONGER AVAILABLE VICTA74
Used Victa G4 Carburettor Body ONLY!
OEM Number CR03504A
1 in stock
Used Victa G4 Carburettor Components
Includes diaphram springs, poppet valve, throttle valve (CR036326A), follower (CR03407A), poppet valve retaining plate and diaphragm cover (CR03636A).
NO LONGER AVAILABLE VICTA83
Used Victa G4 Main Jet, Float and Needle
1 sets in stock
Used Victa Throttle Cable and Control
Fits early Victa 18" rotary mowers that were fitted with G3 carburettored 160cc two stroke engines (as pictured at top of page).
NO LONGER AVAILABLE VICTA78
Used Victa Cylinder Head
Fits Victa 160cc Power Torque engines. No decompression valve installed. New replacement head gaskets are available
here. OEM Number EN73007A
1 in stock
Used Victa Cylinder Head
Fits 160cc Power Torque engines. No decopression valve installed. New head gaskets are available
here. OEM Number EN72515A
2 in stock
Used Victa Cylinder Head
Fits 160cc Power Torque engines. Blanked decompressor hole (not machined/threaded) so decompressor not required or necessary. New head gaskets are available
here. OEM Number EN72515A
1 in stock
Used Victa Power Torque Crankshaft, Con-rod and Piston Assembly
Includes crank pin, gudgeon pin and bearings. OEM Number EN02081A
1 assembly in stock
Used Victa Blower Housing
Fits Victa 125cc 70 series Mark 3 two stroke engines, as fitted to Victa Imperial cylinder mowers.
2 in stock
Used Victa Blower Housing
Fits Victa 160cc 70 series two stroke engines.
1 in stock
Used Victa Power Torque Engine Cover Plate
4 in stock
Used Victa Inner Engine Cover
OEM Number EN72670A
1 in stock
Used Victa Cooling Baffle / Crankcase Shroud
OEM Number EN73058A
1 in stock
Used Victa Cowling / Shroud
Fits Victa Powertorque engines.
NO LONGER AVAILABLE VICTA33
Used Victa Cowling / Shroud
Fits Victa Powertorque engines.
NO LONGER AVAILABLE VICTA68Used Victa Fuel Tank
Includes Cap. No fuel tap included. New replacement fuel taps available
here.
OEM Number EN73061A
2 in stock
Used Victa Fuel Tank Assembly
Includes cap and fuel tap. OEM Number EN72676A
1 in stock
Used Victa Fuel Tank Cap
Suit Victa two stroke fuel tanks with ~60mm diamtere filler neck.
NO LONGER AVAILABLE VICTA80
Used Victa G4 Carburettor Assembly
Fits 160cc 70 series, 80 series and Power Torque engines. Fully cleaned with new primer bowl cap and o-ring installed.
NO LONGER AVAILABLE VICTA49
Used Victa Crankcase Insert / Fan Cover
Fits 160cc Power Torque engines. OEM Numbers EN73000A
1 in stock
Used Victa Crankcase / Governor Fitting
OEM Number CR03727A
2 in stock
Used Victa Power Torque Intake Manifold
Includes 2 x screws and tension washer. OEM Number CR03633A
5 in stock
Used Victa Power Torque Intake Manifold
Includes 2 x screws and tension washer. OEM Number CRO3656A
NO LONGER AVAILABLE VICTA22
Used Blade Blade Carrier / Blade Disc
Fits Victa 18" rotary mowers including VC160 (as pictured at top of page).
1 in stock
Used Victa Blade Carrier / Blade Disc
Fits most Victa 18" models. Distance between bolt hole centres 257mm. Centre hole diametre 19mm. OEM Number CA093386
1 in stock
Used Victa Blade Carrier / Blade Disc
Fits Victa 19" cut models. Overall diametre 304mm. Centre hole diametre 19mm.
NO LONGER AVAILABLE VICTA31
Used Blade Holder Boss / Blade Carrier Boss
Suits Victa 19" cut rotary mowers fitted with Victa 2 stroke engines. Tapered internal bore.
1 in stock
Used Blade Holder Boss / Blade Carrier Boss
Suits four stroke Victa mowers with an engine crankshaft diametre of 7/8 inch. 3/16 inch built-in key.
NO LONGER AVAILABLE VICTA19
Used Victa Lower Handle Bar Stub Pair
Suits most 18" cut models. Includes knobs, bolts and clamp washers.
NO LONGER AVAILABLE VICTA58
Used Victa Handle Bar Knob and Bolt
1 pair in stock
Used Victa Lower Handle Bar Stub Pair
Suits 18" cut Victa Lawnkeeper. Includes knobs, bolts and clamp washers.
1 pair in stock
Used Victa Rear Flap
Suits steel base 18" cut models. Includes spring and shaft.
1 in stock
Used Victa Rear Flap
Suits late model 19 inch cut Victa rotary mowers.
OEM Number CH86251A.
1 in stock
Used Victa 160cc Crankcase Bolt
Suits early 70 & 80 series 160cc Victa two stroke engines. Bolt measures overall 110mm.
4 in stock
Used Victa 160cc Cylinder Mounting Stud Set
Set of upper & lower cylinder mounting studs for early 70 & 80 series 160cc Victa two stroke engines. Upper studs measure overall 175mm. Lower studs measure overall 148mm.
NO LONGER AVAILABLE VICTA16
Used Victa Power Torque Flywheel
OEM Number MA05633A
NO LONGER AVAILABLE VICTA60
Used Victa Power Torque Flywheel and Disc Boss
NO LONGER AVAILABLE VICTA46